View LM2423TE_5186147.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

lm2423 220v monolithic triple channel 15 mhz crt dtv driver general description the lm2423 is a triple channel high voltage crt driver circuit designed for use in dtv applications. the ic contains three high input impedance, wide band amplifiers which directly drive the rgb cathodes of a crt. each channel has its gain internally set to ?54 and can drive crt capacitive loads as well as resistive loads present in other applications, limited only by the package?s power dissipation. the ic is packaged in an industry standard 11-lead to-220 molded plastic power package designed specifically to meet high voltage spacing requirements. see thermal consider- ations section. features n 15 mhz bandwidth at 130v pp output swing n up to 170v pp output swing with ac coupling to cathodes n 0v to 5v input voltage range n stable with 0 pf?20 pf capacitive loads and inductive peaking networks n convenient to-220 staggered thin lead package style applications n ac coupled dtv applications using the 480p format as well as standard ntsc and pal formats. connection diagram schematic diagram 20114801 figure 1. top view order number LM2423TE see ns package number te11b nopb available only with lead free plating 20114802 figure 2. simplified schematic diagram (one channel) july 2004 lm2423 220v monolithic triple channel 15 mhz crt dtv driver ? 2004 national semiconductor corporation ds201148 www.national.com
absolute maximum ratings (notes 1, 3) if military/aerospace specified devices are required, please contact the national semiconductor sales office/ distributors for availability and specifications. supply voltage (v cc ) +250v bias voltage (v bb ) +16v input voltage (v in ) ?0.5v to v bb +0.5v storage temperature range (t stg ) ?65?c to +150?c lead temperature (soldering, < 10 sec.) 300?c esd tolerance, human body model 2 kv machine model 200v junction temperature 150?c jc (typ) 2.2?c/w operating ratings (note 2) v cc +100v to +230v v bb +7v to +13v v in +0v to +5v v out +40v to +215v case temperature 110?c do not operate the part without a heat sink. electrical characteristics (see figure 2 for test circuit) unless otherwise noted: v cc = +220v, v bb = +12v, c l = 10 pf, t c = 50?c. dc tests: v in = +2.75v dc . ac tests: output = 130v pp (60v ? 190v) at 1 mhz. symbol parameter conditions lm2423 units min typ max i cc supply current no input signal, no video input, no output load 14 21 28 ma i bb bias current 9 15 22 ma v out, 1 dc output voltage no ac input signal, v in = 2.75v dc 120 125 130 v dc v out, 2 dc output voltage no ac input signal, v in = 1.25v dc 200 205 210 v dc a v dc voltage gain no ac input signal ?51 ?54 ?57 v/v ? a v gain matching (note 4), no ac input signal 1.0 db le linearity error (notes 4, 5), no ac input signal 8 % t r rise time, 60v to 190v (note 6), 10% to 90% 22 ns +os overshoot 8% t f fall time, 60v to 190v (note 6), 90% to 10% 21 ns ?os overshoot (note 6) 4 % note 1: absolute maximum ratings indicate limits beyond which damage to the device may occur. note 2: operating ratings indicate conditions for which the device is functional, but do not guarantee specific performance limits. for guaranteed specifi cations and test conditions, see the electrical characteristics. datasheet min/max specification limits are guaranteed by design, test, or statistical analy sis. the guaranteed specifications apply only for the test conditions listed. some performance characteristics may change when the device is not operated under the list ed test conditions. note 3: all voltages are measured with respect to gnd, unless otherwise specified. note 4: calculated value from voltage gain test on each channel. note 5: linearity error is the variation in dc gain from v in = 1.15v to v in = 4.35v. note 6: input from signal generator: t r ,t f < 1 ns. lm2423 www.national.com 2
ac test circuit figure 3 shows a typical test circuit for evaluation of the lm2423. this circuit is designed to allow testing of the lm2423 in a 50 ? environment without the use of an expensive fet probe. the two 4990 ? resistors form a 400:1 divider with the 50 ? resistor and the oscilloscope. a test point is included for easy use of an oscilloscope probe. the compensation capacitor is used to compensate the network to achieve flat frequency response. 20114803 note: 10 pf load includes parasitic capacitance. figure 3. test circuit (one channel) lm2423 www.national.com 3
typical performance characteristics (v cc = +220v dc ,v bb = +12v dc ,c l = 10 pf, v out = 130v pp (60v ? 190v), t c = 50?c, test circuit ? figure 3 unless otherwise specified) 20114804 figure 4. v out vs v in 20114805 figure 5. lm2423 pulse response 20114806 figure 6. bandwidth 20114807 figure 7. speed vs load capacitance 20114808 figure 8. speed vs offset 20114809 figure 9. speed vs case temperature lm2423 www.national.com 4
typical performance characteristics (v cc = +220v dc ,v bb = +12v dc ,c l = 10 pf, v out = 130v pp (60v ? 190v), t c = 60?c, test circuit ? figure 3 unless otherwise specified) 201148010 figure 10. power dissipation vs frequency 201148011 figure 11. safe operating area 201148012 figure 12. lm2423 cathode response lm2423 www.national.com 5
theory of operation the lm2423 is a high voltage monolithic three channel crt driver suitable for dtv applications. the lm2423 operates with 220v and 12v power supplies. the part is housed in the industry standard 11-lead to-220 molded plastic power package with thin leads for improved metal-to-metal spacing. the circuit diagram of the lm2423 is shown in figure 2 . the pnp emitter follower, q5, provides input buffering. q1 and q2 form a fixed gain cascode amplifier with resistors r1 and r2 setting the gain at ?54. emitter followers q3 and q4 isolate the high output impedance of the cascode stage from the capacitance of the crt cathode, which decreases the sensitivity of the device to load capacitance. q6 provides biasing to the output emitter follower stage to reduce cross- over distortion at low signal levels. figure 3 shows a typical test circuit for evaluation of the lm2423. this circuit is designed to allow testing of the lm2423 in a 50 ? environment without the use of an expen- sive fet probe. in this test circuit, the two 4.99 k ? resistors form a 400:1 wideband, low capacitance probe when con- nected to a 50 ? coaxial cable and a 50 ? load (such as a 50 ? oscilloscope input). the input signal from the generator is ac coupled to the base of q5. application hints introduction national semiconductor (nsc) is committed to provide ap- plication information that assists our customers in obtaining the best performance possible from our products. the fol- lowing information is provided in order to support this com- mitment. the reader should be aware that the optimization of performance was done using a specific printed circuit board designed at nsc. variations in performance can be realized due to physical changes in the printed circuit board and the application. therefore, the designer should know that com- ponent value changes may be required in order to optimize performance in a given application. the values shown in this document can be used as a starting point for evaluation purposes. when working with high bandwidth circuits, good layout practices are also critical to achieving maximum per- formance. important information the lm2423 performance is targeted for the hdtv market. the application circuits shown in this document to optimize performance and to protect against damage from crt arc over are designed specifically for the lm2423. if another member of the lm242x family is used, please refer to its datasheet. power supply bypass since the lm2423 is a wide bandwidth amplifier, proper power supply bypassing is critical for optimum performance. improper power supply bypassing can result in large over- shoot, ringing or oscillation. 0.1 f capacitors should be connected from the supply pins, v cc and v bb , to ground, as close to the lm2423 as is practical. additionally, a 22 f or larger electrolytic capacitor should be connected from both supply pins to ground reasonably close to the lm2423. arc protection during normal crt operation, internal arcing may occasion- ally occur. this fast, high voltage, high-energy pulse can damage the lm2423 output stage. the application circuit shown in figure 13 is designed to help clamp the voltage at the output of the lm2423 to a safe level. the clamp diodes, d1 and d2, should have a fast transient response, high peak current rating, low series impedance and low shunt capaci- tance. 1ss83 or equivalent diodes are recommended. d1 and d2 should have short, low impedance connections to v cc and ground respectively. the cathode of d1 should be located very close to a separately decoupled bypass capaci- tor (c3 in figure 13 ). the ground connection of d2 and the decoupling capacitor should be very close to the lm2423 ground. this will significantly reduce the high frequency voltage transients that the lm2423 would be subjected to during an arc over condition. resistor r2 limits the arc over current that is seen by the diodes while r1 limits the current into the lm2423 as well as the voltage stress at the outputs of the device. r2 should be a 1 M 2 w solid carbon type resistor. r1 can be a 1 M 4 w metal or carbon film type resistor. having large value resistors for r1 and r2 would be desirable, but this has the effect of increasing rise and fall times. inductor l1 is critical to reduce the initial high frequency voltage levels that the lm2423 would be subjected to. the inductor will not only help protect the device but it will also help minimize rise and fall times as well as minimize emi. for proper arc protection, it is important to not omit any of the arc protection components shown in figure 13 . effect of load capacitance figure 7 shows the effect of increased load capacitance on the speed of the device. this demonstrates the importance of knowing the load capacitance in the application. increas- ing the load capacitance from 10 pf to 20 pf adds about 7 ns to both the rise and fall times. it is important to keep the board capacitance as low as possible to maximize the speed of the driver. effect of offset figure 8 shows the variation in rise and fall times when the output offset of the device is varied from 120v to 130v dc . the rise and fall times both show a variation of about 6% relative to the center data point (125v dc ). the rise time increases in speed with the increase in offset voltage and the fall time decreased in speed with the increase in offset voltage. thermal considerations figure 9 shows the performance of the lm2423 in the test circuit shown in figure 3 as a function of case temperature. the figure shows that both the rise and fall times of the lm2423 increase by approximately 14% as the case tem- perature increases from 30?c to 110?c. this corresponds to a speed degradation of 1.4% for every 10?c rise in case temperature. 20114813 figure 13. one channel of the lm2423 with the recommended application circuit lm2423 www.national.com 6
application hints (continued) figure 10 shows the maximum power dissipation of the lm2423 vs. frequency when all three channels of the device are driving into a 10 pf load with a 130v p-p alternating one pixel on, one pixel off. the graph assumes a 72% active time (device operating at the specified frequency), which is typical in a tv application. the other 28% of the time the device is assumed to be sitting at the black level (190v in this case). this graph gives the designer the information needed to determine the heat sink requirement for his application. the designer should note that if the load capacitance is in- creased the ac component of the total power dissipation would also increase. the lm2423 case temperature must be maintained below 110?c. if the maximum expected ambient temperature is 60?c and the maximum power dissipation is 17w (from figure 10 , 15 mhz) then a maximum heat sink thermal resistance can be calculated: this example assumes a capacitive load of 10 pf and no resistive load. the designer should note that if the load capacitance is increased the ac component of the total power dissipation will also increase. optimizing transient response referring to figure 13 , there are three components (r1, r2 and l1) that can be adjusted to optimize the transient re- sponse of the application circuit. increasing the values of r1 and r2 will slow the circuit down while decreasing over- shoot. increasing the value of l1 will speed up the circuit as well as increase overshoot. it is very important to use induc- tors with very high self-resonant frequencies, preferably above 300 mhz. ferrite core inductors from j.w. miller magnetics (part # 78fr--k) were used for optimizing the performance of the device in the nsc application board. the values shown in figure 13 can be used as a good starting point for the evaluation of the lm2423. using a variable resistor for r1 will simplify finding the value needed for optimum performance in a given application. once the opti- mum value is determined the variable resistor can be re- placed with a fixed value. due to arc over considerations it is recommended that the values shown in figure 13 not be changed by a large amount. figure 12 shows the typical cathode pulse response with an output swing of 130v pp inside a modified sony tv using a sony pre-amp. pc board layout considerations for optimum performance, an adequate ground plane, iso- lation between channels, good supply bypassing and mini- mizing unwanted feedback are necessary. also, the length of the signal traces from the signal inputs to the lm2423 and from the lm2423 to the crt cathode should be as short as possible. the following references are recommended: ott, henry w., ?noise reduction techniques in electronic systems?, john wiley & sons, new york, 1976. ?video amplifier design for computer monitors?, national semiconductor application note 1013. pease, robert a., ?troubleshooting analog circuits?, butterworth-heinemann, 1991. because of its high small signal bandwidth, the part may oscillate in a tv if feedback occurs around the video channel through the chassis wiring. to prevent this, leads to the video amplifier input circuit should be shielded, and input circuit wiring should be spaced as far as possible from output circuit wiring. typical application a typical application of the lm2423 is shown in the sche- matic for the nsc demonstration board in figure 14 . used in conjunction with an lm1246 preamplifier, a complete video channel from input to crt cathode can be achieved. perfor- mance is ideal for dtv applications. the nsc demonstration board can be used to evaluate the lm2423 combination with the lm2485 and the lm1246 in a tv. it is important that the tv designer use component values for the driver output stage close to the values shown in figure 14 . these values have been selected to protect the lm2423 from arc over. diodes d1, d2, d4, and d7?d9 must also be used for proper arc over protection. the nsc demonstration board can be used to evaluate the lm2423 in a tv. if the nsc demonstration board is used for evaluating the lm2423, then u3, the +5v voltage regulator may be used, eliminating the need to route +5v to the neck board for the lm1246. nsc demonstration board figure 15 shows the routing and component placement on the nsc lm2423/lm1246/lm2486 demonstration board. this board provides a good example of a layout that can be used as a guide for future layouts. note the location of the following components: c19?v cc bypass capacitor, located very close to pin 2 and ground pins c20?v bb bypass capacitor, located close to pin 11 and ground c46, c48 ? v cc bypass capacitors, near lm2423 and v cc clamp diodes. very important for arc protection. the routing of the lm2423 outputs to the crt is very critical to achieving optimum performance. figure 16 shows the routing and component placement from pin 10 (v out1 )ofthe lm2423 to the blue cathode. note that the components are placed so that they almost line up from the output pin of the lm2423 to the blue cathode pin of the crt connector. this is done to minimize the length of the video path between these two components. note also that d8, d9, r24, and d6 are placed to minimize the size of the video nodes that they are attached to. this minimizes parasitic capacitance in the video path and also enhances the effectiveness of the pro- tection diodes. the anode of protection diode d8 is con- nected directly to a section of the ground plane that has a short and direct path to the lm2423 ground pins. the cath- ode of d9 is connected to v cc very close to decoupling capacitor c7 which is connected to the same area of the ground trace as d8. the diode placement and routing is very important for minimizing the voltage stress on the lm2423 during an arc over event. this demonstration board uses large pcb holes to accom- modate socket pins, which function to allow for multiple insertions of the lm2423 in a convenient manner. to benefit from the enhanced lm2423 package with thin leads, the device should be secured in small pcb holes to optimize the metal-to-metal spacing between the leads. lm2423 www.national.com 7
application hints (continued) 201148014 figure 14. lm2423/lm1246/lm2485 dtv applications circuit lm2423 www.national.com 8
application hints (continued) 201148016 figure 15. lm2423/lm1246/lm2485 dtv demonstration board layout lm2423 www.national.com 9
application hints (continued) 201148017 figure 16. trace routing and component placement for blue channel output lm2423 www.national.com 10
physical dimensions inches (millimeters) unless otherwise noted note: available only with lead free plating ns package number te11b order number LM2423TE nopb life support policy national?s products are not authorized for use as critical components in life support devices or systems without the express written approval of the president and general counsel of national semiconductor corporation. as used herein: 1. life support devices or systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a significant injury to the user. 2. a critical component is any component of a life support device or system whose failure to perform can be reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness. banned substance compliance national semiconductor certifies that the products and packing materials meet the provisions of the customer products stewardship specification (csp-9-111c2) and the banned substances and materials of interest specification (csp-9-111s2) and contain no ??banned substances?? as defined in csp-9-111s2. national semiconductor americas customer support center email: new.feedback@nsc.com tel: 1-800-272-9959 national semiconductor europe customer support center fax: +49 (0) 180-530 85 86 email: europe.support@nsc.com deutsch tel: +49 (0) 69 9508 6208 english tel: +44 (0) 870 24 0 2171 fran?ais tel: +33 (0) 1 41 91 8790 national semiconductor asia pacific customer support center email: ap.support@nsc.com national semiconductor japan customer support center fax: 81-3-5639-7507 email: jpn.feedback@nsc.com tel: 81-3-5639-7560 www.national.com lm2423 220v monolithic triple channel 15 mhz crt dtv driver national does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and national reserves the righ t at any time without notice to change said circuitry and specifications.

▲Up To Search▲

Price & Availability of LM2423TE

	To Download LM2423TE Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .